Dodge Dart Engine Oil Capacity

Dodge Dart Oil Capacity

If you’re the owner of a Dodge Dart, then you know that it’s important to use the best engine oil for your vehicle. Not all oils are created equal – some are better for certain engines than others. If you’re not sure what type of oil to use, don’t worry! We’re here to help. In this article, we will discuss the best engine oil for Dodge Dart vehicles and provide you with a few recommendations.

The engine oil that was put in at the factory is a high-quality energy conserving type lubricant. Oil changes should be performed at least once every six months, if not more frequently, under normal usage conditions.

2013 2014 2015 2016 Dodge Dart Engine Oil Capacity

2013-2016 Dodge Dart Engine Oil Capacity

2.4L 4-cyl ED8 engine:

  • Engine Oil Capacity with filter: 5.5 quarts (5.2 liters);
  • Oil Type: 0W-20;
  • Oil pan drain plug tightening torque: 30 ft/lbs.

2.4L 4-cyl ED6 engine:

  • Engine Oil Capacity with filter: 5.5 quarts (5.2 liters);
  • Oil Type: 0W-20;
  • Oil pan drain plug tightening torque: 30 ft/lbs.

2.0L 4-cyl ECK engine:

  • Engine Oil Capacity with filter: 5 quarts (4.7 liters);
  • Oil Type: 0W-20;
  • Oil pan drain plug tightening torque: 30 ft/lbs.

2.0L 4-cyl ECN engine:

  • Engine Oil Capacity with filter: 5 quarts (4.7 liters);
  • Oil Type: 0W-20;
  • Oil pan drain plug tightening torque: 30 ft/lbs.

1.4L 4-cyl EAF Turbo engine:

  • Engine Oil Capacity with filter: 4 quarts (3.8 liters);
  • Oil Type: 5W-40;
  • Oil pan drain plug tightening torque: 20 ft/lbs.

How Much Oil Does a Dodge Dart Take?

2.4L Dodge Dart takes 5.5 quarts (5.2 liters) of 0W-20 oil with a filter.

Engine oil must be replaced at the correct level to maintain optimum engine lubrication. Check the oil level on a regular basis, especially during fuel stops. The ideal time to check the oil level is around five minutes after shutting off a fully warmed engine. After waiting overnight, do not check the engine oil level until it has been started up. Checking the engine oil level when the engine is cold will result in an incorrect reading.

Checking the oil while the car is on level ground and just when the engine is hot may improve the accuracy of oil level readings. The range markings on the dipstick should be maintained.

The range markings will be a crosshatch zone that reads SAFE or a crosshatch zone that reads MAX at the low end of the range and MIN at the high end of the range. When the indication reading is below 1 qt (1L), add 1 qt (1L) of oil.

Recommended Engine Oil Capacity For Dodge Dart (PF)

Best Dodge Dart 0W-20 Oil

Best Dodge Dart 5W-40 Oil

Recommended Engine Oil Filter For Dodge Dart

Every time the engine oil is changed, the engine oil filter should be replaced with a new one. All of these manufacturers’ engines have a full-flow type disposable oil filter. For replacement, use a filter of this sort. Replacement filters are available in many different quality levels. Only high-quality filters should be used to guarantee maximum efficiency. MOPAR recommends using high-quality engine oil filters.

Engine Oil Change Intervals

In no case should oil change intervals be greater than 10,000 miles (16,000 km) or 12 months, whichever comes first.

The engine oil change indication system on your vehicle is activated. After a single chime, the EVIC display will show the “Oil Change Required” message for approximately 10 seconds to indicate the next scheduled oil change interval. The engine oil change indicator system is based on a duty cycle, which means that the engine oil change period may vary depending on your driving habits.

The message “Engine Oil Change Indicator System Check” will appear each time you turn the key to the ON/RUN position or cycle the ignition to the ON/RUN position if your vehicle has Keyless Enter-N-GoTM. To turn off the message temporarily, press and release the MENU button. After completing the scheduled maintenance, refer to the following procedure to reset the oil change indicator system (if desired).

Vehicles Equipped With Keyless Enter-N-Go™

  • Without pressing the brake pedal, press the ENGINE START/STOP button and cycle the ignition to the ON/ RUN position (Do not start the engine.)
  • Fully depress the accelerator pedal, slowly, three times within 10 seconds.
  • Without pressing the brake pedal, press the ENGINE START/STOP button once to return the ignition to the OFF/LOCK position.

Vehicles Not Equipped With Keyless Enter-N-Go™

  • Turn the ignition switch to the ON/RUN position (Do not start the engine.)
  • Fully depress the accelerator pedal, slowly, three times within 10 seconds.
  • Turn the ignition switch to the OFF/LOCK position. NOTE: If the indicator message illuminates when you start the vehicle, the oil change indicator system did not reset. If necessary, repeat this procedure.

Last update on 2024-03-23 / Affiliate links / Images from Amazon Product Advertising API

Leave a Comment

Your email address will not be published. Required fields are marked *